Recent questions in Concrete Structures

A rectangular singly reinforced concrete beam has a width of $300 \text{ mm}$ and an effective depth of $550 \text{ mm}.$ The grades of steel and concrete are Fe$500$ and...

A $250 \mathrm{~mm}$ wide $\times 600 \mathrm{~mm}$ deep rectangular concrete beam is prestressed by means of $4$ high-tensile tendons, each of $14 \mathrm{~mm}$ diameter...

Which one of the following is utilized to determine the long-term deformation of concrete under sustained loading?CreepShrinkageModulus of ruptureSplit tensile strength

The required centre-to-centre spacing of $10$ mm diameter bars is $150$ mm to resist the design moment in a concrete slab. Instead of $10$ mm diameter bars, if $12$ mm di...

Select ALL CORRECT option(s) which can be considered to check whether the flexural stresses in a prestressed concrete beam are within the allowable stresses at the transf...

The design shear strength of a reinforced concrete rectangular beam with a width of $250 \: \mathrm{mm}$ and an effective depth of $500 \: \mathrm{mm}$, is $0.3 \: \mathr...

Consider a reinforced concrete beam section of $350 \: \mathrm{mm}$ width and $600\: \mathrm{mm}$ depth. The beam is reinforced with the tension steel of $800 \mathrm{~mm...

A reinforced concrete beam has a support section with width of $300 \: \mathrm{mm}$ and effective depth of $500 \: \mathrm{mm}$ . The support section is reinforced with $...

​​​As per $\mathrm{IS } \: 456: 2000$ provisions for two-way slabs with continuous edges, the longitudinal steel reinforcement to be provided in the edge strip is based o...

Consider a reinforced concrete beam section of $300 \: \mathrm{mm}$ width and $700 \: \mathrm{mm}$ depth. The beam is reinforced with the tension steel of $2000 \: \mathr...

A simply supported, uniformly loaded, two-way slab panel is torsionally unrestrained. The effective span lengths along the short span $\text{(x)}$ and long span $\text{(y...

A concrete column section of size $300 \mathrm{~mm} \times 500 \mathrm{~mm}$ as shown in the figure is subjected to both axial compression and bending along the major axi...

Consider a balanced doubly-reinforced concrete section. If the material and other sectional properties remain unchanged, for which of the following cases will the section...

An inverted $\mathrm{T}$-shaped concrete beam $\text{(B1)}$ in the figure, with centroidal axis $\mathrm{X}-\mathrm{X}$, is subjected to an effective prestressing force o...

A slab panel with an effective depth of $250 \mathrm{~mm}$ is reinforced with $0.2 \%$ main reinforcement using $8 \mathrm{~mm}$ diameter steel bars. The uniform center-t...

$\text{M20}$ concrete as per $\mathrm{IS~} 456: 2000$ refers to concrete with a design mix having ____________an average cube strength of $20~ \mathrm{MPa}$an average cyl...

With regard to the shear design of RCC beams, which of the following statements is/are TRUE? Excessive shear reinforcement can lead to compression failure in concreteBeam...

Consider the singly reinforced section of a cantilever concrete beam under bending, as shown in the figure $(M25$ grade concrete, $Fe415$ grade steel). The stress block p...

Creep of concrete under compression is defined as the _________. increase in the magnitude of strain under constant stress increase in the magnitude of stress under const...

A singly reinforced concrete beam of balanced section is made of $\text{M20}$ grade concrete and $\text{Fe 415}$ grade steel bars. The magnitudes of the maximum compressi...

Consider a doubly reinforced RCC beam with the option of using either $\text{Fe250}$ plain bars or $\text{Fe500}$ deformed bars in the compression zone. The modulus of el...

Read the following statements relating to flexure of reinforced concrete beams:In over-reinforced sections, the failure strain in concrete reaches earlier than the yield ...

A post-tensioned concrete member of span $15 \; \text(m)$ and cross-section of $450 \; \text{mm} \times 450 \; \text{mm}$ is prestressed with three steel tendons, each of...

In the context of elastic theory of reinforced concrete, the modular ratio is defined as the ratio ofYoung's modulus of elasticity of reinforcement material to Young's mo...

A reinforced concrete beam with rectangular cross section (width = $300$ $\text{mm}$, effective depth = $580$ $\text{mm}$) is made of $M30$ grade concrete. It has $1\%$ l...

A rectangular cross-section of a reinforced concrete beam is shown in the figure. The diameter of each reinforcing bar is $\text{16 mm}$. The values of modulus of elastic...

A prismatic cantilever prestressed concrete beam of span length, $L = 1.5 \text{ m}$ has one straight tendon placed in the cross-section as shown in the following figure ...

A dowel bar is placed at a contraction joint. When contraction occurs, the concrete slab cracks at predetermined location(s). Identify the arrangement, which shows the co...

A simply supported prismatic concrete beam of rectangular cross-section, having a span of $8\:m$, is prestressed with an effective prestressing force of $600\:kN$. The ec...

The maximum applied load on a cylindrical concrete specimen of diameter $150\: mm$ and length $300\: mm$ tested as per the split tensile strength test guidelines of $IS\:...

A concrete beam of span $15\: m,\ 150\: mm$ wide and $350\: mm$ deep is prestressed with a parabolic cable as shown in the figure (not drawn to the scale). Coefficient of...

A concrete dam holds $10\: m$ of static water as shown in the figure (not drawn to the scale). The uplift is assumed to vary linearly from full hydrostatic head at the he...

A simply supprted rectangular concrete beam of span $8$ m has to be prestressed with a force of $1600$ kN. The tendon is of parabolic profile having zero eccentricity at ...

In the reinforced beam section shown in the figure $\text{(not drawn to scale)}$, the nominal cover provided at the bottom of the beam as per $\text{IS 456-2000},$ is$\te...

For a given loading on a rectangular plain concrete beam with an overall depth of $500 \: mm$, the compressive strain and tensile strain developed at the extreme fibers a...

Tie bars of $12 \: mm$ diameter are to be provided in a concrete pavement slab. The working tensile stress of the tie bars is $230 \: MPa$, the average bond strength betw...

A $3 \: m \times 3 \: m$ square precast reinforced concrete segments to be installed by pushing them through an existing railway embankment for making an underpass as sho...